search query: @author Nehal, Qaiser / total: 1
reference: 1 / 1
« previous | next »
Author:Nehal, Qaiser
Title:Design of a wideband variable gain amplifier
Publication type:Master's thesis
Publication year:2011
Pages:viii + 56 s. + liitt. 3      Language:   eng
Department/School:Mikro- ja nanotekniikan laitos
Main subject:Piiritekniikka   (S-87)
Supervisor:Halonen, Kari
Instructor:Saari, Ville
Electronic version URL: http://urn.fi/URN:NBN:fi:aalto-201207022651
OEVS:
Electronic archive copy is available via Aalto Thesis Database.
Instructions

Reading digital theses in the closed network of the Aalto University Harald Herlin Learning Centre

In the closed network of Learning Centre you can read digital and digitized theses not available in the open network.

The Learning Centre contact details and opening hours: https://learningcentre.aalto.fi/en/harald-herlin-learning-centre/

You can read theses on the Learning Centre customer computers, which are available on all floors.

Logging on to the customer computers

  • Aalto University staff members log on to the customer computer using the Aalto username and password.
  • Other customers log on using a shared username and password.

Opening a thesis

  • On the desktop of the customer computers, you will find an icon titled:

    Aalto Thesis Database

  • Click on the icon to search for and open the thesis you are looking for from Aaltodoc database. You can find the thesis file by clicking the link on the OEV or OEVS field.

Reading the thesis

  • You can either print the thesis or read it on the customer computer screen.
  • You cannot save the thesis file on a flash drive or email it.
  • You cannot copy text or images from the file.
  • You cannot edit the file.

Printing the thesis

  • You can print the thesis for your personal study or research use.
  • Aalto University students and staff members may print black-and-white prints on the PrintingPoint devices when using the computer with personal Aalto username and password. Color printing is possible using the printer u90203-psc3, which is located near the customer service. Color printing is subject to a charge to Aalto University students and staff members.
  • Other customers can use the printer u90203-psc3. All printing is subject to a charge to non-University members.
Location:P1 Ark Aalto  1211   | Archive
Keywords:wideband
variable gain amplifier
low noise amplifier
low power CMOS
Abstract (eng): Synthetic Aperture Radar (SAR) is a well known technique for imaging the earth's surface.
This thesis presents a wideband variable gain amplifier which can be used in the direct conversion receiver (DCR) for SAR.
The thesis first introduces how to extract the important parameters i.e. gain, bandwidth and noise of the VGA from the overall receiver requirements.
Next, a general design philosophy for the VGA is presented which identifies the main design modules in the amplifier.
Also, a brief introduction to wideband stages and DC-offset compensation techniques is presented.

Then a detailed explanation of the VGA design is given.
Small-signal and noise analyses are presented for the VGA gain stages along with their simulation results.
VGA post-layout simulation results are also shown to verify the functionality of the final layout drawn using 0.13 µm CMOS.

At the end, measurement results for the VGA are given which show that the VGA achieved the desired gain and bandwidth.
However, due to irregular operation of the digital control for the chip, the frequency response of the VGA showed gain peaking.
The measured input noise density of the VGA at different gain settings is also given and it matched well with the simulated value.
Moreover, the input 1 dB compression point and the third order input intercept point results for the VGA are also given.
The overall operation of VGA was deemed satisfactory for the direct conversion receiver for SAR.
Abstract (fin): Synteettisapertuurinen tutka (SAR) on hyvin tunnettu tekniikka maanpinnan kuvantamiseen.
Tässä diplomityössä on suunniteltu laajakaistainen säädettävä vahvistin, jota voidaan käyttää SAR:in suorasekoitusvastaanottimessa (DCR).

Ensin näytetään kuinka tärkeät muuttujat, kuten esimerkiksi VGA:n vahvistus, kaistanleveys ja kohina, saadaan määritettyä vastaanottimen kokonaisvaatimuksista.
Seuraavaksi esitetään yleisesti suunnittelutapa VGA:lle, jossa tunnistetaan VGA:n tärkeimmät suunnittelumoduulit.
Laajakaistaiset asteet, joita voidaan käyttää VGA:n suunnittelussa, esitellään lyhyesti, kuten myös tekniikoita, joilla siirrosjännite saadaan kompensoitua.
Seuraavaksi esitellään yksityiskohtaisesti kuinka VGA suunnitellaan.
Työssä esitetään piensignaali- ja kohina-analyysit VGA:n vahvistusasteille kuten myös simulaatiotulokset.

VGA on suunniteltu ja valmistettu 0.13 µm CMOS prosessilla.
Piirikuvion jälkeiset simulaatiot on myös esitetty ja ne todentavat lopullisen piirikuvion toimivuutta.
Lopuksi esitetään VGA:n mittaustulokset, jotka näyttävät, että halutut vahvistus ja kaistanleveys on saavutettu.
Mikropiirin digitaalisen ohjauksen epätasaisesta toimivuudesta johtuen, VGA:n taajuusvasteessa näkyi vahvistuksen piikittämistä.

VGA:n tulon kohinatiheyden mittaustulokset eri vahvistusasetuksilla on myös esitetty ja ne vastaavat hyvin simuloituja arvoja.
Tulon 1 dB:n kompressiopiste ja tulon kolmannen kertaluvun keskinäismodulaatiosärön leikkauspiste on myös annettu VGA:lle.
Yleisesti ottaen VGA:n toimintaa voidaan pitää onnistuneena SAR:ssa käytettävälle suorasekoitusvastaanottimelle.
ED:2011-06-01
INSSI record number: 42112
+ add basket
« previous | next »
INSSI